Here goes a long post of buying guide, incl Digiprog 3 for sale(best price), update, manual, review, FAQ, car list Welcome! Part 1: Digiprog 3 for sale Price: €144.00 Price: €135.00 Price: €129( 2017 Xmas Sale:€99) Price:€99.00 Price: €79 Price:€404.00 Price:€19.99 ST59 Plug works together with DIGIPROG3 odometer correction tool, used on vehicles with NEC chips, like Ford, Renault and so on. Installation example: Ford NEC. Remove the dashboard and open it. Search on dash the Soldering Points. solder on same points as in picture the cables from ST59 on it.
Flash thermoflash digi 2 hf manual de. Speed light digital player mp4 mp3 elay in english hotpoint wt960 ist siemens siwamat xls 1231 rc-35 spc.
All Pins must be Lift up From Board. Connect the Cables to ST59 you can nothing make Wrong. Now connect the ST 59 with the Digiprog. Select the program: cars / trucks – FORD – KA NEC. The DIGIPROG denotes old / wrong Mileage.
Program and completed the new / correct Mileage. Digiprog 3 software free download digiprog 3 software download digiprog 3 update download digiprog update digiprog 3 password digiprog 3 manual Part 2: digiprog 3 user manual english digiprog 3 download: More info: Tips on using Digiprog 3 odometer programmer:.
Power-On digimaster 3 password:1. Digiprog series not support AUDI A1 A3 Golf 6, if you want to do such model,you can choose Digimaster 3. Always connect the Eeprom to the ST01 or ST04 before you connect to the DigiProg this will avoid Electro static feedback (ESD). Never solder the connections whilst the lead is connected to the programmer, this will damage the DigiProg.
Always keep your DigiProg in its case when not in Use & keep it in a dry environment at night (don’t leave it in the trunk of your car) If you are using solvents to remove lacquers’ from Eeprom’s ensure that they are cleaned 4. Completely as the solvent can damage the clips.
Do not connect the device to your laptop, otherwise you will get blue screen problem. As most of Cars Need to Open Dashboard and Do the Soldering, you’d better have basic knowledge about mileage correction before order Part 3: digiprog 3 update Price: $49.99 Price: $49.99 Digiprog 3 V4.94 Update Notice:. If Your Serial Number of Digiprog 3 is 590C8F0E0000 24CC65070000 AFD68C070000, Can not buy this update file. Please kindly note. It takes 24 hours to send the update file. Please provide correct serial number and close or uninstall anti-virus software on your laptop, otherwise will cause blue screen.
Make sure your computer will not become standby status when updating. Computer power must connect ok. Update will takes 15-20 mins. Please confirm the update file is complete as display below, or will cause blue screen too Digiprog update tips: How to update Digiprog 3 software: 1.Connect the USB to the computer, start your, run Digiloader1.exe. 2.Choose the right port, select Digi1.bin, and Click the button. If your dp3 doesn’t enter blue screen, check your setting and restart from step 1. 3.In upgrading, it should be like this until over.
Attention, it will be damaged if you remove it now. Upgrade Over. Your Digiprog 3 should restart automatically. Part 4: digiprog 3 not working Digiprog 3 not working: Mosaic screen digiprog 3 v4.94 odometer correction masterdisplay with Mosaic as soon as open it up (shown picture below), and it was not working. Solution: ask the vendor for these two chips of digiprog iii (marked red picture below) for free and replace the two chips. It will work. Digiprog 3 not working: white/bluescreen You may encounter with the Blue/White screen problem of china digiprog 3; usually the possible reasons incl:.
a) The first and most common cause of blue screen is the inappropriate update Digiprog 3. We must remember that updates are created for the serial number. The serial number of the update files must = Digiprog 3 serial number. Otherwise, upload the files to another serial number gives us the effect shown in the picture above. b) Another cause of the blue screen may be interrupted during the upgrade of communication between your computer and your device digiprog3. c) Other causes unrelated to update the device And there are two optional solutions here: Solution1: Digiprog3 –101W(X1) Solder Operation Way Cut off the connect cable on the 5pin pad (note: cut via reverse) Then use multimeter to test 5pin and R10 which is far away from the point of X1 end –If open circuit is not ok, then means cut off the connector successfully. Solder X1 to the pad (note: reverse welding) Connect the point which is the end of R10 which is far away from 101W(X1) and the cable and X1-2 pin.
Take off the fly cable between C30 and X1 Take off the IC on the X1 Replace the IC Connect the new IC Connect the fly cable as the original situation Note: the original point of the IC is on the upper left corner, against C30. (Red circled place is chip pic of STC15F: 10W H85330 8AB) Solution 2: Repair Digiprog3 update failure – a blue / White screen. To repair the unit we will need:. a)Update files with the corresponding serial number = serial number of the device.
b)Programmer serial memory for example, willem. Ok, so we begin. We will have 3 digiprog undress and get into the PCB, exactly 2 serial memory. You will see a such a view: Us interested, memory, marked in the picture above. Are respectively a memory U1A and U2A. These are the memories that are 22, feet on one side, which is 44, feet the entire memory. We remove the memory U1A from the plate and put in the programmer.
![]()
Load a file content digi1.bin, to memory U1A. Then again put memory on the board.
Do the same with memory U2A. Only here to load file Digi2.bin Then again put memory U2A on the board. Preferably before each update, do yourself a copy memory dumps U1A and U2A. Then we can go back in case of problems with the update to the old version. U1A = Digi1.bin U2A = Digi2.bin Twirl, back digiprog. After this step, run digiprog. If everything went well that you will be greeted this image.
DigiProg 3 Ram EEprom Digiprog 3 24C1024 The serial number is stored in the file digi1.bin exactly at this point: For example, the serial numbers: C0BE9E0B0000 = D2 CC D0 16 0F 1A 6F F1 00 = CE 5B 56 C6 3F 16 8D 14 F6C428170000 = 87 98 FA 4E 3F E0 06110000 = 44 5B B6 EB 2A A3 D6 1C 3AC928170000 = CF D5 60 29 93 B3 DA D2 Any change in the file, making it not useful after update, blue screen on digiprog 3. The problem is probably in the checksums of the files after editing change. Maybe someday will a program that will allow changing the serial number in the file update. Then buy only 1 time updates and will be able to change the serial number in the file. Those who sell the updates are, surely such a program.
Platine Digiprog 3 Digiprog 3 cable pinouts Part 5: digiprog 3 questions and answers have somebody problem with no conection on every car? i need to buy another obd cable? Easy to change plug but if there is still an issue then it could be inside main unit What is ST01, ST04 cable used for in the package of Digiprog 3? It needs to remove chip when you program mileage for some car models. One end of the ST01 cable and ST04 cable clip the chip, and the other end connect to digiprog3. Audi A5 2011 year 2.0tdi can digi done this dash via obd.
Other places ecu,dsg? Yeah, ecu, dsg and smart key But you will need some special tools for that Can digiwigy do Mercedes clk 270 cdi 2003?
Can do just dash I not understand, why guys you need that dongle. All NEC dashboards (except old Peugeot) can makes by 4 wires only.
No need solder 14 wires.
Comments are closed.
|
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |